# 20513342 Hose Clamp | Genuine Volvo Penta Part

## 🔧 Product Description

This genuine Volvo Penta hose clamp is an OEM service component used in the Charge-Air / Inlet Hose Clamp. It is manufactured to the original Volvo Penta dimensional, material and interface requirements for the documented Volvo Penta 5-litre TAD5 EDC4 generator diesel application. Technical identification: Hose clamp for the crankcase oil-separator/breather hose assembly. In service, it routes the specified fluid or pressure signal between matched components without leakage, restriction, vibration damage or incorrect connection geometry. Selection must be confirmed by OEM part number 20513342, the exact model/product number, serial number and installed assembly configuration.

## 🚤 Compatibility

Typically suits:

-   Volvo Penta TAD720VE
-   Volvo Penta TAD721GE
-   Volvo Penta TAD721VE
-   Volvo Penta TAD722GE
-   Volvo Penta TAD722VE
-   Volvo Penta TAD730GE MECH
-   Volvo Penta TAD730GE EDC4
-   Volvo Penta TAD731GE MECH
-   Volvo Penta TAD731GE EDC4
-   Volvo Penta TAD732GE EDC4
-   Volvo Penta TAD733GE EDC4
-   Volvo Penta TAD532GE EDC4

-   **Engine Family:** TAD

## ⚙️ Key Features

-   Genuine Volvo Penta OEM hose clamp
-   OEM part number 20513342
-   Technical distinction: Hose clamp for the crankcase oil-separator/breather hose assembly
-   Quantity varies by assembly, most commonly one

## 🔌 Function

Routes the specified fluid or pressure signal between matched components without leakage, restriction, vibration damage or incorrect connection geometry. Install without twist or preload, renew the specified seals/clamps, preserve the original routing and pressure- or leak-test the circuit after assembly.

## ⚠️ Common Signs of Failure

-   Visible fluid leakage, dampness or staining along the line or connection
-   Cracking, chafing, corrosion or impact damage
-   Restricted flow caused by deposits, deformation or internal collapse
-   Vibration fretting or failed support at clamps and mounting points

## 🛠️ Service Notes

-   Match the clamp to the hose outside diameter so the band closes well within its working range rather than at the very end of its travel
-   Position it over the spigot behind the bead or barb, with the screw where a driver or spanner can still reach it once everything is refitted
-   Tighten to seal, not to crush — an over-tightened worm-drive clamp cuts into soft hose and starts the leak you were trying to stop
-   Renew clamps when a hose is changed rather than reusing them, and keep band, housing and screw all marine-grade stainless so the clamp does not corrode against itself
-   Where two clamps are fitted to one connection, stagger the screw heads and recheck both after the first running period

## 📦 Condition

-   Genuine Volvo Penta part
-   Brand new
-   Supplied in original or equivalent packaging

## Details

- **Price:** 22.79 AUD
- **Vendor:** Volvo Penta
- **Tags:** Volvo Penta

## Variants

| Variant | Price | Available |
|---------|-------|-----------|
| Default Title | 22.79 AUD | In stock |

## Images

- 20513342 Hose Clamp | Genuine Volvo Penta Part

---

> Source: [Sawley's Auto and Marine](https://www.sawleysautoandmarine.com.au/products/20513342-hose-clamp-genuine-volvo-penta)
> Updated: 2026-08-22