# 21662697 Bilge Pump | Genuine Volvo Penta Part

## 🔧 Product Description

A genuine Volvo Penta marine bilge pump designed for reliable water removal in the specified manual or electrical installation.

## 🚤 Compatibility

Typically suits:

-   Volvo Penta TAMD42WJ-A
-   Volvo Penta TMD22B
-   Volvo Penta TMD22P-C
-   Volvo Penta HS1A
-   Volvo Penta TAMD22P-B
-   Volvo Penta KAMD44P-B
-   Volvo Penta KAMD44P-C
-   Volvo Penta MD22L
-   Volvo Penta MD22P
-   Volvo Penta KAD300-A
-   Volvo Penta KAD32P
-   Volvo Penta KAD43P-A
-   Volvo Penta KAD44P
-   Volvo Penta KAD44P-B
-   Volvo Penta KAD44P-C
-   Volvo Penta KAMD300-A
-   Volvo Penta KAMD43P
-   Volvo Penta KAMD43P-A
-   Volvo Penta KAMD44P-A
-   Volvo Penta KAMD43P-B

-   **Engine Family:** TAMD, TMD, HS, KAMD, MD, KAD

## ⚙️ Key Features

-   Electrical system: 24V
-   Current draw: approximately 10A
-   Hose connections: 37.5mm or 49mm
-   Output: approximately 166L/min
-   Recommended fuse: 15A
-   Approximate dimensions: 150 × 137 × 213mm
-   Double ball bearings, mechanical shaft seal and water-cooled motor

## 🔌 Function

The 24V high-capacity pump evacuates bilge water in heavy-duty marine applications.

## ⚠️ Common Signs of Failure

-   Low pumping capacity
-   Motor or bearing noise
-   Mechanical seal leakage
-   Impeller blockage
-   Blown fuse
-   Excessive electrical current

## 🛠️ Service Notes

-   Mount the pump at the lowest point of the bilge where it will actually pick up, sitting level and secured so it cannot topple or shift at sea, and keep it clear of debris that would jam the impeller
-   Take the discharge hose up to a loop above the waterline before it turns down to the outlet so the sea cannot siphon back into the boat, and clamp the hose properly at both ends
-   Wire the pump on its own protected circuit with cable sized for the length of the run, and make every connection above the level bilge water can reach, using proper waterproof joints rather than tape
-   Test the pump and its float or sensing switch by filling the bilge and watching it lift, run and cut out, and repeat the test at the start of each season
-   Treat it as a nuisance-water pump rather than damage control — keep the strainer clear and the bilge dry enough that a new leak would be obvious

## 📦 Condition

-   Genuine Volvo Penta part
-   Brand new
-   Supplied in original or equivalent packaging

## Details

- **Price:** 506.48 AUD
- **Vendor:** Volvo Penta
- **Type:** Pumps
- **Tags:** Volvo Penta

## Variants

| Variant | Price | Available |
|---------|-------|-----------|
| Default Title | 506.48 AUD | In stock |

## Images

- 21662697 Bilge Pump | Genuine Volvo Penta Part

---

> Source: [Sawley's Auto and Marine](https://www.sawleysautoandmarine.com.au/products/21662697-bilge-pump-genuine-volvo-penta)
> Updated: 2026-10-10