{"product_id":"1677855-pipe-connection-genuine-volvo-penta","title":"1677855 Pipe Connection | Genuine Volvo Penta Part","description":"\u003ch2\u003e\n 🔧 Product Description\n\u003c\/h2\u003e\n\u003cp\u003e\n This genuine Volvo Penta pipe connection is a machined coolant-pipe connection used in the water-pump\/thermostat-housing pipe connection. It is manufactured to the original Volvo dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. Catalogue cross-description: stand-pipe\/end connection. In service, it provides the fixed coolant-pipe connection at the water-pump or thermostat housing. Selection must be confirmed by OEM part number 1677855, the exact engine\/product model, serial number and the installed assembly configuration.\n\u003c\/p\u003e\n\u003ch2\u003e\n 🚤 Compatibility\n\u003c\/h2\u003e\n\u003cp\u003e\n Typically suits:\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Volvo Penta TWD1240VE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1241GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1242GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1240GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1241VE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1242VE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1241-42VE\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Engine Family:\n  \u003c\/strong\u003e\n  TWD, TAD\n \u003c\/li\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Serial Range:\n  \u003c\/strong\u003e\n  SN-2012369406\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n ⚙️ Key Features\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  OEM Volvo Penta part number 1677855\n \u003c\/li\u003e\n \u003cli\u003e\n  System group: Cooling System\n \u003c\/li\u003e\n \u003cli\u003e\n  Net weight: 0.635 kg\n \u003c\/li\u003e\n \u003cli\u003e\n  Serial-referenced application - verify against engine serial number\n \u003c\/li\u003e\n \u003cli\u003e\n  Fits TWD1240VE and TAD1240, TAD1241 and TAD1242 series engines\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔌 Function\n\u003c\/h2\u003e\n\u003cp\u003e\n The pipe connection provides a sealed, correctly aligned junction between coolant pipework and the component it feeds. It positions the pipe run accurately so hoses and clamps seat properly and coolant flow is unrestricted.\n\u003c\/p\u003e\n\u003ch2\u003e\n ⚠️ Common Signs of Failure\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Coolant leakage or staining at the connection face\n \u003c\/li\u003e\n \u003cli\u003e\n  Corrosion, pitting or scaling of the connection body\n \u003c\/li\u003e\n \u003cli\u003e\n  Cracking at the flange, thread or brazed joint\n \u003c\/li\u003e\n \u003cli\u003e\n  Distorted or damaged sealing face preventing a leak-free joint\n \u003c\/li\u003e\n \u003cli\u003e\n  Repeated hose failure at the connection caused by a rough or corroded surface\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🛠️ Service Notes\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Clean the threads and sealing face in the housing, and check the bore of the connection is clear before fitting\n \u003c\/li\u003e\n \u003cli\u003e\n  Fit a new sealing washer, O-ring or gasket, and where a tapered thread is used seal it with the product the manual specifies rather than winding tape onto a fuel, oil or hydraulic joint\n \u003c\/li\u003e\n \u003cli\u003e\n  Hold the connection at the correct angle for the pipe run as it is tightened, so the pipe meets it squarely instead of being sprung into place\n \u003c\/li\u003e\n \u003cli\u003e\n  Tighten to the figure in the workshop manual, and do not try to cure a weep by pulling the joint up harder — strip it and look at the sealing face\n \u003c\/li\u003e\n \u003cli\u003e\n  Pressure-test or run the system and check for weeping before closing up access, then check the joint again after the first period of running\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 📦 Condition\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Genuine Volvo Penta part\n \u003c\/li\u003e\n \u003cli\u003e\n  Brand new\n \u003c\/li\u003e\n \u003cli\u003e\n  Supplied in original or equivalent packaging\n \u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Volvo Penta","offers":[{"title":"Default Title","offer_id":53381045289252,"sku":"6565708","price":174.12,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0994\/8115\/7924\/files\/original_3e89424d-1101-4796-a521-69515f0a1d06.jpg?v=1788054541","url":"https:\/\/www.sawleysautoandmarine.com.au\/products\/1677855-pipe-connection-genuine-volvo-penta","provider":"Sawley's Auto and Marine","version":"1.0","type":"link"}