{"product_id":"191271-washer-genuine-volvo-penta","title":"191271 Washer | Genuine Volvo Penta Part","description":"\u003ch2\u003e\n 🔧 Product Description\n\u003c\/h2\u003e\n\u003cp\u003e\n This genuine Volvo Penta washer is a load-distributing and spacing component manufactured to the specified diameter, thickness and material used in the engine or propulsion fastener load-distribution point. It is manufactured to the original Volvo Penta dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. In service, it distributes fastener load and sets the specified spacing at the joint. Selection must be confirmed by OEM part number 191271, the exact engine or product model, serial number and installed configuration.\n\u003c\/p\u003e\n\u003ch2\u003e\n 🚤 Compatibility\n\u003c\/h2\u003e\n\u003cp\u003e\n Typically suits:\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Volvo Penta TWD1630G\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1211P\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1210G\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1210P\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1210PB\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1211G\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TD1210G\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TD121GP\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TD121GPB\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1230G\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1230V\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1231GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TAD1232GE\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Engine Family:\n  \u003c\/strong\u003e\n  TWD, TD, TAD\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n ⚙️ Key Features\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  OEM part number 191271\n \u003c\/li\u003e\n \u003cli\u003e\n  Fit in the original orientation beneath the correct fastener and inspect the mating surfaces for wear or fretting.\n \u003c\/li\u003e\n \u003cli\u003e\n  TH=6mm (Volvo assembly listing)\n \u003c\/li\u003e\n \u003cli\u003e\n  Quantity varies by assembly, most commonly one\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔌 Function\n\u003c\/h2\u003e\n\u003cp\u003e\n Distributes fastener load and sets the specified spacing at the joint. Fit in the original orientation beneath the correct fastener and inspect the mating surfaces for wear or fretting.\n\u003c\/p\u003e\n\u003ch2\u003e\n ⚠️ Common Signs of Failure\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Permanent cupping, cracking or distortion\n \u003c\/li\u003e\n \u003cli\u003e\n  Fretting, polished movement marks or elongation around the hole\n \u003c\/li\u003e\n \u003cli\u003e\n  Loss of clamp load or loosening of the associated fastener\n \u003c\/li\u003e\n \u003cli\u003e\n  Incorrect spacing or misalignment of the retained component\n \u003c\/li\u003e\n \u003cli\u003e\n  Corrosion or surface damage reducing effective support area\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🛠️ Service Notes\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Check you are fitting the same type of washer that came out — plain, hardened, sealing and locking washers are not interchangeable, and the wrong one either fails to seal or fails to hold\n \u003c\/li\u003e\n \u003cli\u003e\n  Treat sealing washers on fuel, oil and coolant unions as single-use; they seal by deforming onto the faces, so a used one will not seal reliably a second time\n \u003c\/li\u003e\n \u003cli\u003e\n  Clean the seating faces and make sure the washer sits flat and square, fully under the head or nut, before tightening — a washer trapped on a chamfer or edge will crush unevenly\n \u003c\/li\u003e\n \u003cli\u003e\n  Tighten the fastener to the figure given in the workshop manual for your engine, and account for every washer on reassembly so none is left loose inside a housing or the engine bay\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 📦 Condition\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Genuine Volvo Penta part\n \u003c\/li\u003e\n \u003cli\u003e\n  Brand new\n \u003c\/li\u003e\n \u003cli\u003e\n  Supplied in original or equivalent packaging\n \u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Volvo Penta","offers":[{"title":"Default Title","offer_id":53384177058084,"sku":"5648086","price":5.97,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0994\/8115\/7924\/files\/original_f59569fd-307d-42ec-8fa0-16fe11e4fd49.jpg?v=1788057993","url":"https:\/\/www.sawleysautoandmarine.com.au\/products\/191271-washer-genuine-volvo-penta","provider":"Sawley's Auto and Marine","version":"1.0","type":"link"}