{"product_id":"20524754-pulley-genuine-volvo-penta","title":"20524754 Pulley | Genuine Volvo Penta Part","description":"\u003ch2\u003e\n 🔧 Product Description\n\u003c\/h2\u003e\n\u003cp\u003e\n This genuine Volvo Penta pulley is an OEM service component used in the Coolant-Pump Pulley. It is manufactured to the original Volvo Penta dimensional, material and interface requirements for the documented Volvo Penta 16-litre TWD16 industrial diesel application. Technical identification: Coolant-pump pulley, catalogue key 25. In service, it locates and drives the associated rotating component while maintaining belt or gear alignment, speed ratio, run-out and shaft support. Selection must be confirmed by OEM part number 20524754, the exact model\/product number, serial number and installed assembly configuration.\n\u003c\/p\u003e\n\u003ch2\u003e\n 🚤 Compatibility\n\u003c\/h2\u003e\n\u003cp\u003e\n Typically suits:\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Volvo Penta TWD1644-45GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1682-83GE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1683VE\n \u003c\/li\u003e\n \u003cli\u003e\n  Volvo Penta TWD1672-1673GE\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Engine Family:\n  \u003c\/strong\u003e\n  TWD\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n ⚙️ Key Features\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  OEM part number 20524754\n \u003c\/li\u003e\n \u003cli\u003e\n  Technical distinction: Coolant-pump pulley, catalogue key 25\n \u003c\/li\u003e\n \u003cli\u003e\n  Inspect the mating shaft\/key\/spline, install with the correct press or puller method, align belt\/gear tracks and verify run-out and fastener torque.\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔌 Function\n\u003c\/h2\u003e\n\u003cp\u003e\n Locates and drives the associated rotating component while maintaining belt or gear alignment, speed ratio, run-out and shaft support. Inspect the mating shaft\/key\/spline, install with the correct press or puller method, align belt\/gear tracks and verify run-out and fastener torque.\n\u003c\/p\u003e\n\u003ch2\u003e\n ⚠️ Common Signs of Failure\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Abnormal torsional vibration, rattling or cyclic noise\n \u003c\/li\u003e\n \u003cli\u003e\n  Pulley, flywheel or hub run-out and belt-tracking problems\n \u003c\/li\u003e\n \u003cli\u003e\n  Cracking, wear or damage at the hub, spokes or mounting face\n \u003c\/li\u003e\n \u003cli\u003e\n  Loose fasteners, fretting or damaged key\/spline interface\n \u003c\/li\u003e\n \u003cli\u003e\n  Accessory-drive, starting or timing problems caused by misalignment\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🛠️ Service Notes\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Inspect the belt running surfaces before fitting — a pulley with glazed, scored, pitted or rust-roughened grooves will chew through a new belt in very little running time\n \u003c\/li\u003e\n \u003cli\u003e\n  Check that the pulley runs true and that its bearing or bush turns smoothly with no roughness or side play; fit a new belt whenever a pulley is changed\n \u003c\/li\u003e\n \u003cli\u003e\n  Confirm that every pulley in the drive lies in the same plane and that the belt profile matches each groove — misalignment shows up as belt dust, squeal or a worn belt edge and will destroy a new belt quickly\n \u003c\/li\u003e\n \u003cli\u003e\n  Fit onto a clean, dry, burr-free shaft or hub face and tighten the retaining fasteners in the sequence and to the figures given in the workshop manual for your engine\n \u003c\/li\u003e\n \u003cli\u003e\n  Turn the engine over by hand before starting to confirm the belt is fully seated in every groove and that nothing fouls, then recheck belt tension after the first running period\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔄 Supersession \u0026amp; Cross Reference\n\u003c\/h2\u003e\n\u003ch3\u003e\n OEM Supersession Chain\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  20524754 → Supersedes 20451516\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\n OEM \/ Related Numbers\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  20451516 earlier number superseded by this part\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\n Aftermarket \/ Verified Equivalents\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Auger: 55697\n \u003c\/li\u003e\n \u003cli\u003e\n  Sampa: 030.290\n \u003c\/li\u003e\n \u003cli\u003e\n  DT Spare Parts: 2.15450\n \u003c\/li\u003e\n \u003cli\u003e\n  Bergkraft: BK8401106\n \u003c\/li\u003e\n \u003cli\u003e\n  DSS: 220030\n \u003c\/li\u003e\n \u003cli\u003e\n  IMEX: IMX00420524754\n \u003c\/li\u003e\n \u003cli\u003e\n  SRP: P-24754\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 📦 Condition\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Genuine Volvo Penta part\n \u003c\/li\u003e\n \u003cli\u003e\n  Brand new\n \u003c\/li\u003e\n \u003cli\u003e\n  Supplied in original or equivalent packaging\n \u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Volvo Penta","offers":[{"title":"Default Title","offer_id":53379318612260,"sku":"8970052","price":357.64,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0994\/8115\/7924\/files\/original_293ab10c-994a-4c07-8c33-dc524b7faf29.png?v=1788054690","url":"https:\/\/www.sawleysautoandmarine.com.au\/products\/20524754-pulley-genuine-volvo-penta","provider":"Sawley's Auto and Marine","version":"1.0","type":"link"}