{"product_id":"21586294-unit-injector-genuine-volvo-penta","title":"21586294 Unit Injector | Genuine Volvo Penta Part","description":"\u003ch2\u003e\n 🔧 Product Description\n\u003c\/h2\u003e\n\u003cp\u003e\n A genuine electronically controlled unit injector used on Volvo Penta D9A2L marine commercial engines. Its calibration matches the D9A2L combustion, output and emissions requirements.\n\u003c\/p\u003e\n\u003ch2\u003e\n 🚤 Compatibility\n\u003c\/h2\u003e\n\u003cp\u003e\n Typically suits:\n\u003c\/p\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Volvo Penta D9A2L MH\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Engine Family:\n  \u003c\/strong\u003e\n  D\n \u003c\/li\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   HP Range:\n  \u003c\/strong\u003e\n  Approximately 425-575 HP\n \u003c\/li\u003e\n \u003cli\u003e\n  \u003cstrong\u003e\n   Year Range:\n  \u003c\/strong\u003e\n  Approximately 2005 - 2012\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n ⚙️ Key Features\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Genuine Volvo Penta electronically controlled unit injector\n \u003c\/li\u003e\n \u003cli\u003e\n  Integrates high-pressure pumping, metering and injection nozzle\n \u003c\/li\u003e\n \u003cli\u003e\n  Engine-calibration-specific fuel delivery\n \u003c\/li\u003e\n \u003cli\u003e\n  Genuine Volvo Penta remanufactured alternative available\n \u003c\/li\u003e\n \u003cli\u003e\n  New sealing components must be used during installation\n \u003c\/li\u003e\n \u003cli\u003e\n  Engine type: 9.4L inline six-cylinder turbocharged marine diesel\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔌 Function\n\u003c\/h2\u003e\n\u003cp\u003e\n Creates high injection pressure and delivers the electronically timed fuel charge for one cylinder.\n\u003c\/p\u003e\n\u003ch2\u003e\n ⚠️ Common Signs of Failure\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Cylinder misfire, rough idle or reduced power\n \u003c\/li\u003e\n \u003cli\u003e\n  Excessive smoke or abnormal exhaust temperature\n \u003c\/li\u003e\n \u003cli\u003e\n  Fuel dilution of the engine oil or high fuel consumption\n \u003c\/li\u003e\n \u003cli\u003e\n  Injector-balance, electrical-circuit or combustion fault codes\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🛠️ Service Notes\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Work scrupulously clean: cap or plug the fuel connections as soon as they are opened and keep grit out of the injector bore and off the injector body — contamination is the commonest cause of a new unit injector failing early\n \u003c\/li\u003e\n \u003cli\u003e\n  Fit new O-rings and sealing washers throughout, lightly lubricated on assembly so they slide into the bore without rolling or being nipped\n \u003c\/li\u003e\n \u003cli\u003e\n  Inspect the copper sleeve in the head while the injector is out; a sleeve that is disturbed, corroded or leaking must be renewed with the proper sleeve tooling before the injector goes back\n \u003c\/li\u003e\n \u003cli\u003e\n  Clean the injector seat and the sealing area at the top of the bore, and check the hold-down clamp and yoke for wear or distortion — a bent clamp will let combustion gases past\n \u003c\/li\u003e\n \u003cli\u003e\n  Tighten the clamp and set the unit injector adjustment to the procedure, sequence and figures in the workshop manual for your engine, bleed the fuel system before cranking, and where the engine management holds injector calibration or trim data, program the new injector in\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 🔄 Supersession \u0026amp; Cross Reference\n\u003c\/h2\u003e\n\u003ch3\u003e\n OEM Supersession Chain\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  3801439 - genuine Volvo Penta remanufactured injector\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\n OEM \/ Related Numbers\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  276948 - injector O-ring \/ sealing kit\n \u003c\/li\u003e\n \u003cli\u003e\n  21801388 - injector yoke\n \u003c\/li\u003e\n \u003cli\u003e\n  21344774 - injector retaining screw\n \u003c\/li\u003e\n \u003cli\u003e\n  990073 - cable tie\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\n Other-Brand OEM Numbers\n\u003c\/h3\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Delphi BEBE4C10001 - injector manufacturer cross-reference\n \u003c\/li\u003e\n \u003cli\u003e\n  Delphi: BEBE4C15001\n \u003c\/li\u003e\n \u003cli\u003e\n  Delphi: HRE338\n \u003c\/li\u003e\n \u003cli\u003e\n  Delphi: BEBE4C15001-12B1\n \u003c\/li\u003e\n \u003cli\u003e\n  Lucas: LDFC0388\n \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\n 📦 Condition\n\u003c\/h2\u003e\n\u003cul\u003e\n \u003cli\u003e\n  Genuine Volvo Penta part\n \u003c\/li\u003e\n \u003cli\u003e\n  Brand new\n \u003c\/li\u003e\n \u003cli\u003e\n  Supplied in original or equivalent packaging\n \u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Volvo Penta","offers":[{"title":"Default Title","offer_id":53385849766180,"sku":"D268274","price":2541.15,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0994\/8115\/7924\/files\/original_c86f0016-7fa6-40d4-ab93-f868985f82a7.jpg?v=1777199478","url":"https:\/\/www.sawleysautoandmarine.com.au\/products\/21586294-unit-injector-genuine-volvo-penta","provider":"Sawley's Auto and Marine","version":"1.0","type":"link"}