1366129 Guide Sleeve | Genuine Volvo Penta Part

🔧 Product Description

Genuine Volvo Penta guide sleeve for D3 series marine diesel engines. This small precision sleeve locates and aligns mating components during assembly, keeping bolted or pressed joints correctly positioned. It is a low-cost consumable item that should be inspected whenever the assembly it supports is disturbed.

🚤 Compatibility

• Engine Family: D
• HP Range: 110-220 HP
• Year Range: Approximately 2003 - 2007

Full model list at the end of this description.

⚙️ Key Features

• OEM Volvo Penta part number 1366129
• Net weight 0.006 kg
• Fits Volvo Penta D3 series marine diesel engines, inboard and sterndrive variants
• Small precision alignment component intended for exact component location
• Engine type: Volvo Penta first-generation D3 inline 5-cylinder common-rail diesel
• 2 used per assembly

🔌 Function

A guide sleeve provides an accurate location point so that mating parts align correctly when assembled and stay in position under load. It prevents lateral movement and misalignment that would otherwise place stress on fasteners and joint faces.

⚠️ Common Signs of Failure

• Visible wear, scoring or ovality on the sleeve bore or outer surface
• Loose or sloppy fit allowing movement between the mated components
• Corrosion or pitting preventing correct seating
• Misalignment of the assembly during reassembly, or difficulty locating components
• Deformation or damage caused by previous removal

🛠️ Service Notes

• Check the sleeve and the part that runs in or on it for scoring, ovality, corrosion and pick-up; renew both if either is worn, since a worn pair will never locate correctly
• Clean the bore and the housing before fitting and remove any burrs or corrosion that would stop the sleeve going fully home
• Press or drive the sleeve in square with a tool that bears on its end face rather than on its bore or edge, and seat it fully against its shoulder
• Where the sleeve carries lubricant or a seal, make sure any oil hole lines up, and renew the adjacent seal or O-ring at the same time
• Check that the shaft or fastener it guides moves without binding once the sleeve is home

🔄 Supersession & Cross Reference

OEM / Related Numbers

• 1256394 related guide sleeve
• 8687868 related cap plug
• 9458178 related sealing ring
• 30713237 related plug
• 1383730 related locating pin
• 30750943 related piston-cooling valve
• 8631501 related guide rail

📦 Condition

• Genuine Volvo Penta part
• Brand new
• Supplied in original or equivalent packaging

🔎 Full Model Compatibility

Typically suits:

• Volvo Penta D3-110I-B, D3-110I-C, D3-130I-C, D3-220I-G, D3-130A-A, D3-160A-A, D3-130A-B, D3-160A-B, D3-130A-C, D3-160A-C, D3-140A-D, D3-170A-D, D3-200A-D, D3-220A-D, D3-140I-D, D3-140A-E, D3-170A-E, D3-200A-E, D3-220A-E, D3-140I-E, D3-140A-F, D3-170A-F, D3-200A-F, D3-220A-F, D3-140I-F, D3-140A-G, D3-170A-G, D3-200A-G, D3-220A-G, D3-140I-G, D3-190A-B, D3-190A-C, D3-190I-A, D3-110I-A, D3-130I-A, D3-160I-A, D3-110I-D, D3-150I-D, D3-170I-D, D3-200I-D, D3-220I-D, D3-110I-E, D3-150I-E, D3-170I-E, D3-200I-E, D3-220I-E, D3-110I-F, D3-150I-F, D3-170I-F, D3-200I-F, D3-220I-F, D3-110I-G, D3-150I-G, D3-170I-G, D3-200I-G, D3-110I-H, D3-160I-C, D3-190I-B, D3-190I-C, D3-140A-H, D3-170A-H, D3-200A-H, D3-220A-H, D3-130I-B, D3-160I-B, D3-150I-H, D3-170I-H, D3-200I-H, D3-220I-H, D3-140I-H