1665312 Rubber Cushion | Genuine Volvo Penta Part

🔧 Product Description

This genuine Volvo Penta rubber cushion is a vibration-isolating rubber support used in the radiator/cooling-package vibration isolation. It is manufactured to the original Volvo dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. In service, it isolates the cooling package from engine and chassis vibration while maintaining controlled support. Selection must be confirmed by OEM part number 1665312, the exact engine/product model, serial number and the installed assembly configuration.

🚤 Compatibility

• Engine Family: TWD, TAD

Full model list at the end of this description.

⚙️ Key Features

• OEM Volvo Penta part number 1665312
• System group: Cooling System
• Net weight 0.043 kg
• Fits TAD and TWD series VE industrial diesel engines, including TAD940-952VE, TAD1140-1180VE, TAD1240-1252VE, TAD1340-1385VE and TWD1240VE
• Genuine Volvo Penta replacement component
• 4 used per assembly

🔌 Function

The rubber cushion acts as a flexible isolator between the cooling package and its mounting points, absorbing vibration and shock loads. This reduces stress on radiator and cooler components while keeping them correctly located.

⚠️ Common Signs of Failure

• Cracked, split or crumbling rubber from age, heat and oil exposure
• Compressed or flattened cushion allowing the cooling package to sit out of alignment
• Increased vibration or rattling noise from the radiator or cooler assembly
• Chafing, wear or stress cracking on adjacent brackets, hoses and cooler tanks
• Loose or shifting mounting hardware caused by the cushion no longer taking up movement

🛠️ Service Notes

• Keep oil, fuel and solvents off the rubber during and after fitting; contamination softens and swells the rubber and destroys the isolation it is there to provide
• Tighten only enough to hold the part square and secure — a cushion has to stay slightly compressed to isolate vibration, and crushing it makes the mounting solid
• Where several cushions support one component, renew them as a set so the load shares evenly; a single new cushion alongside aged ones carries more than its share
• Check the bracket, spacer, washers and fasteners at the same time — a cushion that has failed early usually points to a loose fastener, a missing spacer or corrosion in the mounting
• Renew aged cushions whenever the component they support is disturbed; old rubber takes a permanent set and will not recover

🔄 Supersession & Cross Reference

OEM / Related Numbers

• Mounting plate 1665309
• Rubber cushion 1665322
• Spacer 1676648

📦 Condition

• Genuine Volvo Penta part
• Brand new
• Supplied in original or equivalent packaging

🔎 Full Model Compatibility

Typically suits:

• Volvo Penta TAD1241VE, TAD1241-42VE
• Volvo Penta TAD1250VE, TAD1250-52VE
• Volvo Penta TAD1140-42VE
• Volvo Penta TAD1150-52VE
• Volvo Penta TAD1170-72VE
• Volvo Penta TAD1180-83VE
• Volvo Penta TAD1242VE
• Volvo Penta TAD1251VE
• Volvo Penta TAD1252VE
• Volvo Penta TAD1340VE
• Volvo Penta TAD1341VE
• Volvo Penta TAD1342VE
• Volvo Penta TAD1343VE
• Volvo Penta TAD1344VE
• Volvo Penta TAD1345VE
• Volvo Penta TAD1350VE
• Volvo Penta TAD1351-53VE
• Volvo Penta TAD1371-75VE
• Volvo Penta TAD1381-85VE
• Volvo Penta TAD940VE
• Volvo Penta TAD941VE
• Volvo Penta TAD942VE
• Volvo Penta TAD943VE
• Volvo Penta TAD950VE
• Volvo Penta TAD951VE
• Volvo Penta TAD952VE
• Volvo Penta TWD1240VE