1695592 Shaft | Genuine Volvo Penta Part

🔧 Product Description

This genuine Volvo Penta shaft is a machined rotating drive shaft used in the gear and toothed-wheel shaft position. It is manufactured to the original Volvo dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. Approximate component weight: 0.219 kg. In service, it supports and transmits rotation through the designated gear or toothed-wheel assembly. Selection must be confirmed by OEM part number 1695592, the exact engine/product model, serial number and the installed assembly configuration.

🚤 Compatibility

• Engine Family: TAMD, TWD, TID, TD, TAD

Full model list at the end of this description.

⚙️ Key Features

• Genuine Volvo Penta OEM shaft
• OEM part number 1695592
• Approximate component weight: 0.219 kg
• Inspect bearing journals, splines/keys and end-float surfaces; lubricate and set axial clearance to specification

🔌 Function

The shaft carries rotary motion and torque between two points in the steering assembly, running in bearings or bushes at each end. Its straightness and bearing surface condition determine how precisely steering input is transmitted.

⚠️ Common Signs of Failure

• Excessive play, backlash or lost motion at the steering
• Wear, scoring or stepping on the bearing journals
• Bent or distorted shaft causing binding through the range of travel
• Corrosion or pitting on the shaft surface
• Noise, notchiness or roughness when the steering is turned

🛠️ Service Notes

• Handle and store the shaft so the bearing journals and seal running surfaces stay unmarked — a nick on a seal track will cause a leak that no new seal will cure
• Remove the protective coating and check the shaft for straightness, scoring, pitting and stepped wear at the journals, splines and seal areas before fitting
• Lubricate journals, splines and seal surfaces with clean oil of the grade specified for the assembly as it goes together, and renew the seals and any single-use nuts or locking devices disturbed on removal
• Draw bearings and couplings on square with a press or drawing tool that loads only the correct race — hammering a bearing onto a shaft marks the races and can distort the shaft
• Set end float, backlash and shim thickness to the values in the workshop manual for your unit, then turn the assembly by hand to confirm it is free before applying power

🔄 Supersession & Cross Reference

Aftermarket / Verified Equivalents

• OURI: OVSP-016

📦 Condition

• Genuine Volvo Penta part
• Brand new
• Supplied in original or equivalent packaging

🔎 Full Model Compatibility

Typically suits:

• Volvo Penta TAMD74P-A, TAMD74P-B, TAMD74A, TAMD74C-A, TAMD74C-B, TAMD74L-A, TAMD74L-B
• Volvo Penta TD61A, TD61ACE, TD61AG, TD61AGP, TD61AP, TD61APB, TD61AW
• Volvo Penta TD71A, TD71ACE, TD71AG, TD71AGP, TD71AP, TD71APB, TD71AW
• Volvo Penta TID71A, TID71AG, TID71AGP, TID71AP, TID71APB
• Volvo Penta TAMD63L-A, TAMD63P-A
• Volvo Penta TAMD73P-A, TAMD73WJ-A
• Volvo Penta TD610M, TD610V
• Volvo Penta TD630ME, TD630VE
• Volvo Penta TD730ME, TD730VE
• Volvo Penta TID61AG, TID61AGP
• Volvo Penta TWD630ME, TWD630VE
• Volvo Penta TAD730V
• Volvo Penta TAMD71B
• Volvo Penta TAMD72A
• Volvo Penta TAMD75P-A
• Volvo Penta TD640VE
• Volvo Penta TWD610V
• Volvo Penta TWD710V
• Volvo Penta TWD730ME
• Volvo Penta TWD731VE
• Volvo Penta TWD740VE