1695966 Thrust Washer | Genuine Volvo Penta Part

🔧 Product Description

This genuine Volvo Penta thrust washer is a turbocharger axial-thrust control washer used in the turbocharger rotor thrust-washer position. It is manufactured to the original Volvo dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. In service, it controls turbocharger rotor axial movement and transfers thrust load into the bearing system. Selection must be confirmed by OEM part number 1695966, the exact engine/product model, serial number and the installed assembly configuration.

🚤 Compatibility

• Engine Family: TD, TWD, TID, TAD

Full model list at the end of this description.

⚙️ Key Features

• OEM Volvo Penta part number 1695966
• System group: Inlet and Exhaust System
• Net weight: 0.005 kg
• Fits TD, TWD, TID and TAD series industrial and generator-set engines

🔌 Function

The thrust washer carries axial load between a rotating component and its housing, holding the assembly in its correct axial position. It provides a sacrificial bearing surface so wear occurs on the washer rather than the more expensive components.

⚠️ Common Signs of Failure

• Excessive endfloat measured in the assembly
• Scoring, grooving or blueing of the washer face
• Material transfer or break-up of the bearing surface
• Metal debris found in the oil or on the drain plug
• Noise or vibration from the assembly under load

🛠️ Service Notes

• Note which way round each washer comes off and refit it the same way; where one face is grooved or lined, that face runs against the moving part
• Measure the end float or running clearance after fitting and compare it with the figure in the workshop manual for your engine — thrust washers are what sets it, and some are supplied in more than one thickness
• Renew the pair or the full complement together, never one new washer alongside a used one
• Check the faces the washer bears against for scoring, ridging or heat discolouration and clean off any pick-up before assembly
• Oil the washer and its seat on assembly and prime the lubrication system before the engine is turned under power

🔄 Supersession & Cross Reference

OEM / Related Numbers

• Rotor kit 863845
• Lock nut 1695964
• Sleeve 1695965
• Bushings 1695970
• Thrust bearing 1697670
• Splash plate 1695972

📦 Condition

• Genuine Volvo Penta part
• Brand new
• Supplied in original or equivalent packaging

🔎 Full Model Compatibility

Typically suits:

• Volvo Penta TID121KG, TID121KGP, TID121KP, TID121KPB, TID121L, TID121LG, TID121LGP, TID121LP, TID121LPB, TID121K, TID121K-87
• Volvo Penta TD100G-85, TD100G, TD100GG, TD100GGP, TD100HP, TD100HPB, TD100GG-85, TD100GP, TD100GP-85
• Volvo Penta TID100KG, TID100KGP, TID100K, TID100K-87, TID100KGP-87, TID100KP, TID100KP-87, TID100KPB-87
• Volvo Penta TD121G-87, TD121GGP-87, TD121G, TD121GG, TD121GGP, TD121GP, TD121GPB
• Volvo Penta TAD1030G, TAD1030V, TAD1030VE
• Volvo Penta TWD1210G, TWD1210P, TWD1210PB
• Volvo Penta TWD1211P, TWD1211G
• Volvo Penta TAD1230G
• Volvo Penta TAD1231GE
• Volvo Penta TAD1232GE
• Volvo Penta TD1010G
• Volvo Penta TD1030VE
• Volvo Penta TD120HP
• Volvo Penta TD1210G
• Volvo Penta TWD1010G
• Volvo Penta TWD1030ME
• Volvo Penta TWD1031VE
• Volvo Penta TWD1230ME