183582 Needle Roller Bushing | Genuine Volvo Penta Part

🔧 Product Description

This genuine Volvo Penta needle roller bushing is a precision rolling-element or raceway component used in the legacy drive/reverse-gear needle-bushing service position. It is manufactured to the original Volvo dimensional, material and interface requirements so the serviced assembly retains its designed alignment, sealing, load capacity and operating reliability. In service, it provides compact radial support for the matched shaft or pivot in the legacy drive/reverse-gear assembly. Selection must be confirmed by OEM part number 183582, the exact engine/product model, serial number and installed configuration.

🚤 Compatibility

• Engine Family: TAMD, TWD, TID, TD, TAD

Full model list at the end of this description.

⚙️ Key Features

• OEM Volvo Penta part number 183582
• Needle roller bushing - drawn-cup type, presses into the housing
• Net weight 0.012 kg
• Fits TAMD, TWD, TID, TD and TAD series marine diesel engines

🔌 Function

Provides compact radial support for the matched shaft or pivot in the legacy drive/reverse-gear assembly. Measure shaft and housing fits, renew contaminated lubricant and related seals, and install using force only through the race being fitted. Set preload or end float to the applicable Volvo Penta specification.

⚠️ Common Signs of Failure

• Whining or rumbling from the bearing position
• Scoring or wear ridges on the shaft or pin
• Needles loose, missing or seized
• Increased play at the supported component
• Fine metallic debris in the oil

🛠️ Service Notes

• Press only on the stamped, marked end face of the outer shell — that face is made to take the fitting load, and pressing on the opposite end will fold the thin shell over
• Use a proper mandrel with a pilot to enter the bearing square and support the shell right across its face; never hammer directly on the shell and never press on the rollers or the cage
• Check the housing bore is clean, undamaged and within the size the manual for your engine gives; a drawn-cup needle bearing takes its running clearance from the bore, so a worn or oval housing will ruin a new bearing
• Inspect the shaft or journal the rollers run on and renew it if scored or worn — needle rollers mark a shaft, and a new bearing on a scored shaft will not last
• Press to the depth the workshop manual specifies rather than clamping the shell hard against a shoulder in the housing, lubricate as the manual for your engine specifies, then turn the assembly over by hand and check it runs free before any load goes on it

🔄 Supersession & Cross Reference

OEM / Related Numbers

• 276174 small-parts repair kit (includes 183582)
• 271561 gasket/service kit relationship

📦 Condition

• Genuine Volvo Penta part
• Brand new
• Supplied in original or equivalent packaging

🔎 Full Model Compatibility

Typically suits:

• Volvo Penta TAMD74P-A, TAMD74P-B, TAMD74A, TAMD74C-A, TAMD74C-B, TAMD74L-A, TAMD74L-B
• Volvo Penta TD61A, TD61ACE, TD61AG, TD61AGP, TD61AP, TD61APB, TD61AW
• Volvo Penta TD71A, TD71ACE, TD71AG, TD71AGP, TD71AP, TD71APB, TD71AW
• Volvo Penta TID71A, TID71AG, TID71AGP, TID71AP, TID71APB
• Volvo Penta TAMD63L-A, TAMD63P-A
• Volvo Penta TAMD73P-A, TAMD73WJ-A
• Volvo Penta TD610M, TD610V
• Volvo Penta TD630ME, TD630VE
• Volvo Penta TD730ME, TD730VE
• Volvo Penta TID61AG, TID61AGP
• Volvo Penta TWD630ME, TWD630VE
• Volvo Penta TAD730V
• Volvo Penta TAMD71B
• Volvo Penta TAMD72A
• Volvo Penta TAMD75P-A
• Volvo Penta TD640VE
• Volvo Penta TWD610V
• Volvo Penta TWD710V
• Volvo Penta TWD730ME
• Volvo Penta TWD731VE
• Volvo Penta TWD740VE