21513426 O-Ring | Genuine Volvo Penta Part
21513426 O-Ring | Genuine Volvo Penta Part
Couldn't load pickup availability
Available from Volvo Penta international
Typically reaches our store in 10–14 business days
Availability checked daily with Volvo Penta
✓ Authorised Volvo Penta Dealer · Genuine Volvo Penta parts · Ships Australia-wide
🔧 Product Description
A genuine Volvo Penta elastomer O-ring used to seal the component joint specified for part number 21513426. The correct material, cross-section and diameter are required to maintain fluid or pressure containment under engine heat, vibration and repeated service cycles.
🚤 Compatibility
- Engine Family: V
- HP Range: 225-320 HP
Full model list at the end of this description.
⚙️ Key Features
- Genuine Volvo Penta sealing O-ring
- Factory-specified diameter and cross-section
- Designed for engine-temperature and fluid exposure
- Prevents leakage through the mating joint
- Direct replacement for the same numbered original seal
- Engine type: Volvo Penta marine or industrial engine system
🔌 Function
Forms a compressed seal between mating components to prevent fluid loss, air entry or pressure leakage.
⚠️ Common Signs of Failure
- Fluid seepage around the sealed joint
- Flattening, hardening or swelling of the O-ring
- Cuts, nicks or twisting during installation
- Loss of system pressure
- Recurring leakage caused by an incorrect seal size or damaged sealing groove
🛠️ Service Notes
- Always fit a new O-ring — never refit one that has been removed, as it has already taken a set in its groove
- Clean the groove and both sealing faces and check them for nicks, scoring and corrosion pitting; a damaged groove will leak however good the new seal is
- Smear the ring with a little clean lubricant compatible with the fluid it seals, then roll it into place by hand so it sits untwisted and fully in its groove
- Never lever an O-ring over a sharp edge or thread with a screwdriver; use a blunt plastic tool and protect any edge the ring has to pass
- Assemble the joint squarely and tighten to the figure and sequence given in the workshop manual for your engine — over-tightening extrudes the ring and causes the very leak you were curing
📦 Condition
- Genuine Volvo Penta part
- Brand new
- Supplied in original or equivalent packaging
🔎 Full Model Compatibility
Typically suits:
- Volvo Penta V8-270-C-B, V8-270-CE-B, V8-300-C-A, V8-300-CE-A, V8-300-C-B, V8-320-C-B, V8-320-CE-B, V8-300-CE-B, V8-320-C-A, V8-320-CE-A, V8-225-C-A, V8-225-CE-A, V8-225-C-B, V8-225-CE-B, V8-270-C-A, V8-270-CE-A
- Volvo Penta 5.7GXiC-320-R, 5.7GXiCE-320-R, 5.7GXiC-P, 5.7GXiCE-P, 5.7GiC-300-P, 5.7GiCE-300-P, 5.7GiC-300-R, 5.7GiCE-300-R, 5.0GiC-225-S, 5.0GiCE-225-S, 5.0GXiC-P, 5.0GXiCE-P, 5.0GXiC-270-R, 5.0GXiCE-270-R
Shipping & Delivery
Shipping & Delivery
Flat-rate shipping Australia-wide — $14.99 per order, no matter how many parts you add. Orders dispatch from our Kadina, South Australia store. Need it urgently or want to collect in person? Call us on 0412 532 984 before ordering.
Returns & Warranty
Returns & Warranty
14-day change-of-mind returns — if it's not right or you ordered the wrong part, send it back within 14 days in new, unused condition for a refund or exchange. Manufacturer warranties apply to new parts. Full details in our Refunds & Returns policy.
Not sure this fits?
Not sure this fits?
Ask us before you buy — we check part numbers and fitment every day. Call 0412 532 984 (Mon–Fri 8.30am–4.30pm) or message us through the contact page with your engine or vehicle details.
Share
