21849618 O-Ring | Genuine Volvo Penta Part
21849618 O-Ring | Genuine Volvo Penta Part
Couldn't load pickup availability
Available from Volvo Penta international
Typically reaches our store in 10–14 business days
Availability checked daily with Volvo Penta
✓ Authorised Volvo Penta Dealer · Genuine Volvo Penta parts · Ships Australia-wide
🔧 Product Description
Sealing O-ring used in the Volvo Penta installation of the optional Knorr 360 cc single-cylinder air compressor. It seals the assigned compressor or connection joint against air, oil or crankcase leakage.
🚤 Compatibility
- Engine Family: TAD, D, TADH
Full model list at the end of this description.
⚙️ Key Features
- Knorr 360 cc one-cylinder air-compressor application
- Factory cross-section and diameter
- Suitable for compressor operating temperature
- Direct replacement seal
- Use lubricant and torque specified for the joint
- Engine type: Heavy-duty industrial diesel with 360 cc single-cylinder air-compressor option
🔌 Function
Seals the specified air-compressor joint so system pressure and lubricant remain contained.
⚠️ Common Signs of Failure
- Air or oil leakage at the joint
- Pressure loss from the compressor circuit
- Flattened, cut or hardened seal
- Leak recurring after compressor removal
- Visible extrusion or chemical damage
🛠️ Service Notes
- Always fit a new O-ring — never refit one that has been removed, as it has already taken a set in its groove
- Clean the groove and both sealing faces and check them for nicks, scoring and corrosion pitting; a damaged groove will leak however good the new seal is
- Smear the ring with a little clean lubricant compatible with the fluid it seals, then roll it into place by hand so it sits untwisted and fully in its groove
- Never lever an O-ring over a sharp edge or thread with a screwdriver; use a blunt plastic tool and protect any edge the ring has to pass
- Assemble the joint squarely and tighten to the figure and sequence given in the workshop manual for your engine — over-tightening extrudes the ring and causes the very leak you were curing
📦 Condition
- Genuine Volvo Penta part
- Brand new
- Supplied in original or equivalent packaging
🔎 Full Model Compatibility
Typically suits:
- Volvo Penta D8A2-A MP, D8A5-A MH, D8A6-A MH, D8A5-A MG, D8A6-A MG, D8A1-A MP, D8A3-A MP, D8A4-A MP
- Volvo Penta TAD840GE, TAD840-43VE, TAD840GE-B
- Volvo Penta TAD570-72VE, TAD570-71VE-B
- Volvo Penta TAD880-82GE, TAD880-84VE
- Volvo Penta TADH880-82GE, TADH880-84VE
- Volvo Penta TAD540-42VE
- Volvo Penta TAD550-51VE
- Volvo Penta TAD552VE
- Volvo Penta TAD580-83VE
- Volvo Penta TAD841-43GE
- Volvo Penta TAD850-52VE
- Volvo Penta TAD851-53GE
- Volvo Penta TAD853VE
- Volvo Penta TAD870-73VE
Shipping & Delivery
Shipping & Delivery
Flat-rate shipping Australia-wide — $14.99 per order, no matter how many parts you add. Orders dispatch from our Kadina, South Australia store. Need it urgently or want to collect in person? Call us on 0412 532 984 before ordering.
Returns & Warranty
Returns & Warranty
14-day change-of-mind returns — if it's not right or you ordered the wrong part, send it back within 14 days in new, unused condition for a refund or exchange. Manufacturer warranties apply to new parts. Full details in our Refunds & Returns policy.
Not sure this fits?
Not sure this fits?
Ask us before you buy — we check part numbers and fitment every day. Call 0412 532 984 (Mon–Fri 8.30am–4.30pm) or message us through the contact page with your engine or vehicle details.
Share
